Watch how Wall Ace Toolsâ„¢

Streamlines the construction rough framing process…

Wall Pullers

Wall Cups

Pry Bars

Streamline your Construction Rough Framing Process

Wall Ace Tools make rough carpentry easier, safer, and more efficient. You won’t have to cut a hole in a wall or leave a soffit unfinished just to run a cable, chain, or a strap for hoisting and placing a wall panel.

Buy Wall Aceâ„¢ Tools

Good framing carpenters know

that it’s inefficient to cut holes in walls or leave soffits unfinished in order to run a lifting cable, chain, or strap. Doing so requires blocking or patching the hole in the wall and the house wrap, and you risk damaging soffits or fascia. That’s extra work, and it’s not a good use of your time and money.

You can avoid wasting time and money by having to go back just a patch a hole; and you can avoid the risk of damaging a soffit.

The Wall Aceâ„¢ Tools System changes all that!

Our durable Wall Ace Pry Bar, Wall Cups, and Wall Pullers allow you to:

  • Manage labor costs by avoiding damage or having to make repairs
  • Increase production by getting more done in less time

Grow your business with the Wall Ace Tools System by staying ahead of rising material and labor costs!

​See How Wall Ace Tools Work

STEP-BY-STEP Tutorial on building walls with the Wall Ace system

Wall Ace Tools make rough carpentry easier, safer, and more efficient.

 You won’t have to cut a hole in a wall or leave a soffit unfinished just to run a cable, chain, or a strap for hoisting and placing a wall panel.

You can avoid wasting time and money by having to go back just a patch a hole; and you can avoid the risk of damaging a soffit.

Step 1

Using the wall ace big bar, lift the top plates making sure that the bar position is over a joist to avoid damage to the floor when lifting. Slide the appropriate block under the wall. Use an upright two-by-four for the 2×4 wall cups and an upright two by six for the 2×6 wall cups.

Step 2

Place the bar under the cup where you want to apply it. The weight of the bar will lift the cup tight to the plates so that you can fill all the nail holes. Make sure that the bottom of the wall cup is tight against the top plates at all times. You can also perform this procedure without the pry bar if you prefer.

Step 3

Fill all the nail holes with three-inch 16 D nails. We recommend using double headed nails when attaching to avoid damage to the wall cup when pulling the nails out.

Step 4

Note that sheathing must be fastened to the wall where the cups are used to prevent the studs and top plates from tearing apart when lifting. Wall cups must always be spaced evenly on the top plates so that the wall panel is balanced and stays level. It must not flex while suspended.

Determine the wall cup placement by dividing the wall length into thirds.  Attach the cups evenly in the middle third.

Step 5

The chain length and wall cup spacing must be such that the sling forms an angle of no more than 90 degrees. Use the proper lifting apparatus and don’t exceed your equipment’s maximum weight limitation. You may need additional wall cups to perform a wall lift in a level position and to keep the wall from flexing.

Step 6

All lifts should be safe, slow and controlled. The closer you are to a straight or vertical lift; the safer the lift. When the wall panel is in place it must be braced making sure that it is stable and plumb.

Step 7

Now use your wall ace wall pullers; available in various sizes, to bring the wall into its proper position. Once the panel is set; braced securely, and nailed down you can remove the wall cups. Never try to loosen adjust or move a wall cup during use unless the panel is lying flat on the ground or when it is set embraced in place.

Safety First!

Wall Ace is all about safety, so here are some important guidelines to remember:

  • You must follow all applicable OSHA and other standards that may apply to your worksite.
  • Use at least two wall Cups for each wall lift.
  • Use this product only for lifting wood frame sheathed the walls with a three-inch nominal double top plat thickness.
  • Never position the cup side face down during use
  • Never alter or misuse this product